3500/22M 146031-01 Bently Nevada RIM Firmware Interface Module

Description

3500/22M 146031-01 Remove the RIM from the 3500 rack.
Remove the Top Shield from the RIM.
Remove the original firmware IC from the RIM PWA.
Install the upgrade firmware IC into the socket on the RIM PWA.
Replace the RIM Top Shield.
Replace the RIM into the 3500 system.
Reconfigure the RIM using the 3500 Rack Configuration software.
The following pages contain detailed instructions for some of the steps listed above.
Please review completely before proceeding.

Install the upgrade firmware IC into the PWA. Be sure to match the notched end of
the IC to the notched end of the socket. Ensure that the IC is firmly seated in the
socket.
Top Shield Replacement
Replace the top shield. Position the notch on the top shield so that it is at the top left
corner of the module as shown in the diagram under “Top Shield Removal”. Align the
holes in the top shield with the standoffs and press down around each standoff until
they snap in place.
Real-Time Clock Failure
The Real-Time Clock component on the Rack Interface Module uses an internal
lithium battery that must be replaced every 3 to 10 years. The replacement
interval depends on environmental conditions such as operating temperature. A
discharged lithium battery may cause loss of operating information if the rack
loses power. Refer to the System Event List Messages in Section 6 for the
message that will be displayed when the Real-Time Clock must be replaced.
Contact your nearest Bently Nevada office for instructions on how to handle this.

This section describes how to troubleshoot a problem with the Rack Interface
Module or the I/O modules by using the information provided by the verification
screen, the LEDs, the System Event List, and the Alarm Event List. You can display
the verification screen and the two event lists by using the Rack Configuration
Software.
Verification
To perform the Rack Interface Module’s verification:
1. Connect a computer running the Rack Configuration Software to the 3500 rack (if
needed).
2. Select Utilities from the main screen of the Rack Configuration Software.
3. Select Verification from the Utilities menu.
4. Select the Rack Interface Module and select the channel you want to verify.
5. Press the Verify button.
6. Select the Front Port or the Rear Port to get the status.
7. The Module OK State will show the Rack Interface Module’s status and the
Channel OK State will show the channel’s status.

Identifies the module that the event is associated with. If
a half-height module is installed in the upper slot or a
full-height module is installed, the field will be 0 to 15. If
a half-height module is installed in the lower slot, then
the field will be 0L to 15L. For example, the module is
installed in the lower position of slot 5 (5L).
The following System Event List Messages may be placed in the list by the Rack
Interface Module and are listed in numerical order. If an event marked with a star
(*) occurs the…
• Host link on the back of the Rack Interface I/O Module supplying the message will
not communicate with the host computer
• other Rack Interface Modules in the daisy chain will still be able to communicate
with the host computer
• both ports of the Data Manager I/O Module will stop communicating
If you are unable to solve any of these problems, contact your nearest Bently
Nevada Corporation office.

Details: If you need urgent delivery orders, please feel free to contact us, and we will try our best to meet your needs.
Price problem: If you find that other suppliers offer cheaper prices for the same product, we are also willing to provide you with reference prices and give you further discounts.
Contact Us:+86 18106937731
Whatapp:+86 15359293870
Email: geabbdcs@gmail.com / 2872270648@qq.com
Contact Person: Chen

135785-01 3500/93 Display Unit, non backlighted
135785-02 3500/93 Display Unit, back-lighted
137412-01 3500/93 Manual
135799-01 3500/93 Display Interface Module
135799-02 3500/93 Display Interface Module
(use with A05 option only)
135813-01 3500/93 Display Interface I/O
Module
136634-0010-01 10 Foot (3 metres) Cable (PVC)
136634-0050-01 50 Foot (15 metres) Cable (PVC)
136634-0050-02 50 Foot (15 metres) Cable
(Teflon? )
136634-0100-01 100 Foot (30 metres) Cable (PVC)
136634-0100-02 100 Foot (30 metres) Cable
(Teflon? )
130121-02-01 500 Foot (152 metres) Extension
Cable (PVC)
130121-02-02 500 Foot (152 metres) Extension
Cable (Teflon? )
02200271 External Power Supply for 115 Vac
02200272 External Power Supply for 230 Vac
138227-01 Cable Adapter
146085-01 Power Cable
137224-01 System Mounting Assembly
(sheet metal for A01 & A05
options)
04309007 4-40 X 0.63 Phillips head screw for
System Mounting Assembly, 4 are
required