Bently 3500/22M 138607-01 Transient Data Interface Front and Rear Size Cards

Description

3500/22M 138607-01 Table 1 summarizes available monitor types in the

3500 System. Each monitor occupies a single slot in

the rack. All monitors are microprocessor-based and

offer digitally adjustable Alert and Danger setpoints

for each channel1. Users can configure alarms for

latching or non-latching operation. 3500/22M 138607-01 Status

indications for each monitor and channel are

provided with bright, front-panel LEDs, allowing

observation without operator interaction for easy

and convenient operation. Most monitors provide

independent 4 to 20 mA proportional outputs for

each channel of the I/O module for connection to

strip chart recorders or for older process control

systems that do not support a digital interface.

Where applicable, 3500/22M 138607-01 the monitor’s I/O modules provide

transducers with appropriate power via short

circuit-protected terminals. OK detection routines

within each monitor continuously check the integrity

of each transducer and the associated field wiring.

Transducer input signals are buffered and sent to

front-panel coaxial connectors2. Buffered output

terminals are also available upon request on the rear

of the TDI/RIM’s I/O module.

1. 3500/22M 138607-01 In addition to the direct measurement made by the monitor,

many channel types provide an enhanced data set consisting of a

variety of proportional values that will depend on the monitor type

and its configuration. For example, for a radial vibration channel

this includes the basic overall (direct) vibration amplitude as well as

gap voltage, 1X filtered amplitude, 1X filtered phase, 2X filtered

amplitude, 2X filtered phase, NOT 1X amplitude, and Smax. These

additional proportional values are provided for each channel, and

ALERT alarm setpoints can be established on each proportional

value, as desired. DANGER alarm setpoints can be established on

any two proportional values returned from each channel.

2. 3500/60, /62, and /63 monitor types do not provide front-panel

buffered output connectors.

3. Only standard differential expansion capabilities provided. For

ramp differential expansion and complementary input differential

expansion, use the 3500/45 Position Monitor instead.

4. The 3500/42M provides individual 4 to 20 mA proportional

outputs for each channel. The 3500/40M does not provide 4 to 20

mA outputs.

5. 3500/22M 138607-01 The monitor channels are programmed in pairs and can perform

up to two of these functions at a time. Channels 1 and 2 can

perform one function, while channels 3 and 4 perform another (or

the same) function.

6. Channels configured for velocity or acceleration provide only

direct amplitude. Channels configured for Velocity II or Acceleration

II provide 1X amplitude/phase and 2X amplitude/phase in addition

to direct amplitude.

7. Any vibration channel can be configured for conventional “pie

shaped” acceptance region alarms. When configured for circular

acceptance regions, circular, rather than pie-shaped, acceptance

region alarms can be enabled. Refer to the 3500/42M

Operations/Maintenance Manual for additional information, or

contact your nearest sales professional.

8. Contact the factory or your local sales professional for details.
9. Only channels 3 and 4 can be used for Case Expansion

measurements.

10. The 3500/46M provides frequency response 3500/22M 138607-01 characteristics

suitable for use on machines with very slow rotational speeds, such

as hydraulic turbine/generator sets, which often operate at speeds

of 100 RPM or lower. Also, special signal conditioning and tracking

filtering is provided, allowing detection of rough load zone

operation, shear pin failure, and other hydro-specific conditions.

11. The 3500/50 is not intended for use in overspeed protection

applications. Use the 3500/53 instead.

12. Zero speed functionality requires both channels of the 3500/50

module, making it a single-channel monitor.

13. The 3500/53 is a single channel module, intended for use as

part of a 1-out-of-2 or 2-out-of-3 (recommended) overspeed

detection system.

14. The 3500/60 and 3500/61 provide identical functions except the

3500/60 does not provide 4 to 20 mA proportional outputs. When

these outputs are required, use the 3500/61.

15. The 3500/62 is designed to accept static proportional signals

such as 4 to 20 mA, 1 to 5 Vdc, or any static proportional signal

between –10 and +10 Vdc. 3500/22M 138607-01 When dynamic signals (i.e., those where

waveform information is required) are used, a 3500/40M or

3500/42M can often be programmed as a custom channel type to

such signals, making the 3500 system compatible with virtually any

static or dynamic signal from pressure, level, temperature, vibration,

flow, position, speed, or other transducers. Consult the factory or

your local Bently Nevada sales professional for more information.

16. The 3500/64M is primarily intended for monitoring combustor

pressure pulsation instabilities (“humming”) in gas turbines.

Why are the prices of many products of our company more competitive?
(1) Source purchase to reduce the price difference in the intermediate phase
(2) Stable channel and more guaranteed supply
Lead time problem
(1) For the spot products in stock, the delivery can be arranged on the same day after the contract payment is signed
(2) Order products and deliver according to the quoted delivery date
Xiamen Xiongba adheres to the enterprise philosophy of “improving the value of spare parts supply chain”,
For the simple purchase procedure of spare parts, ensure that they are delivered to the site in a timely manner, and help users reduce the risk of downtime caused by the shortage of spare parts
The emergency spare parts support service is complete, and the user can customize the spare parts. The quality of the spare parts is reliable. All the spare parts provided enjoy a one-year super long warranty
Spot stock, fast response, reduce user capital investment, improve spare parts utilization, spare parts replacement!

Details: If you need urgent delivery orders, please feel free to contact us, and we will try our best to meet your needs.
Price problem: If you find that other suppliers offer cheaper prices for the same product, we are also willing to provide you with reference prices and give you further discounts.
Contact us:+86 180 6092 3929
Mail: 2235954483@qq.com
Contact: Chen