GE IS200HFPAG1ACB high-frequency AC power board

Description

GE General Electric Technical Specifications: IS200HFPAG1ACB

Remote baseplates IC693CHS393F (and later) and IC693CHS399E (and later) have a change

inside the baseplate which eliminates the need to IS200HFPAG1ACB remove pin 1 from the mating cable. When

using factory made Wye cable with these baseplates, it is not necessary to remove pin 1 from

the cable. Custom built Wye cables for these baseplates can be made using either Figure 10-20

or Figure 10-21. Figure 10-21 shows how the standard (factory made) Wye cables are made.

By removing pin 1 in custom built Wye cables made for the earlier versions of remote

baseplates, the pin 7 (0V) signal reference originates in the main (CPU) baseplate. In these

earlier versions of the remote IS200HFPAG1ACB baseplates, pin 1 was tied to pin 7 (0V) and also AC coupled to

the remote frame ground. When using these baseplates in combination with the 100% shielded

Wye cables, the pin 7 (0V) reference would be improperly DC coupled to the remote frame

ground through the D-subminiature connector shell, which is DC coupled to the remote frame

ground.

In the remote baseplates IC693CHS393F (and later) and IC693CHS399E (and later), the pin 1

shield signal is DC coupled to the remote frame ground and not attached to pin 7 (0V). This

allows the best noise immunity by IS200HFPAG1ACB providing a good continuous cable shield, and still allows the

pin 7 (0V) signal reference to originate in the CPU baseplate without the need for removing pin

1 in any factory or custom built cable. The D-subminiature connector shell is still DC coupled

to the remote frame ground.

Making a 100% Shielded Cable

Use the following steps to build a 100% shielded cable:

1. Strip approximately 5/8 inch of insulation from your custom cable to expose the shield.
2. Remove the male Pin 1 from any connector plugging directly into an older version remote

baseplate (IC693CHS393E, IC693CHS399D, or earlier).

3. Put split-ring ferrule over cable insulation (Figure 10-17).
4. Fold the shield back over top of the cable insulation and ferrule.
5. Place the collar of the metal hood over top of the folded shield and securely clamp the

hood.

6. Test your cable for continuity between both connector shells. Connect an ohmmeter

between the shells and flex the cable at both ends. If the metalized connector hood is not

making proper contact with the cable shield at either end, the connection will show

intermittent continuity on the ohmmeter.

7. Plug the metal hooded cable onto a remote baseplate expansion port connector or into a GE

Fanuc WYE cable and securely tighten the two screws. Installing and tightening the

screws will electrically connect the shield to the remote baseplate frame ground, which

should in turn should be connected to earth ground as instructed in the “Installation”

chapter, under the heading “Baseplate Safety Grounding.”

Why are the prices of many products of our company more competitive?
(1) Source purchase to reduce the price difference in the intermediate phase
(2) Stable channel and more guaranteed supply
Lead time problem
(1) For the spot products in stock, the de

The maximum number of 8-Channel Analog Current/Voltage Output modules that can be installed

in a system are:

4 in a system using CPU Models 311, 313, or 323

8 in a system using CPU Model 331

32 in a system using CPU Models 340 and 341

64 in a system using CPU Models 350 – 364

Other Configuration Considerations

When planning the module configuration for your application you must also consider the load

capacity of the installed power supply and the total load requirements of all modules that are

installed in the baseplate.

Refer to Chapter 1 in this manual for details on power supply, baseplate, and module load

requirements. The following table lists the specifications for this module. Note that test conditions,

unless otherwise noted, are: VUSER = 24 VDC at an ambient temperature of 25 C (77 F)

livery can be arranged on the same day after the contract payment is signed
(2) Order products and deliver according to the quoted delivery date
Xiamen Xiongba adheres to the enterprise philosophy of “improving the value of spare parts supply chain”,
For the simple purchase procedure of spare parts, ensure that they are delivered to the site in a timely manner, and help users reduce the risk of downtime caused by the shortage of spare parts
The emergency spare parts support service is complete, and the user can customize the spare parts. The quality of the spare parts is reliable. All the spare parts provided enjoy a one-year super long warranty
Spot stock, fast response, reduce user capital investment, improve spare parts utilization, spare parts replacement!

Details: If you need urgent delivery orders, please feel free to contact us, and we will try our best to meet your needs.
Price problem: If you find that other suppliers offer cheaper prices for the same product, we are also willing to provide you with reference prices and give you further discounts.
Contact us:+86 181 0693 7731
Mail: 2872270648@qq.com
Contact: Chen