GE IS200ICCAH1ADB MARK VI INNOVATION DRIVE CONTROL

Description

GE General Electric Technical Specifications: IS200ICCAH1ADB

The 489 is equipped with 3 independent serial communications ports supporting a subset of Modbus RTU protocol. The

front panel RS232 has a fixed baud rate of 9600 and a fixed IS200ICCAH1ADB data frame of 1 start/8 data/1stop/no parity. The front port is

intended for local use only and will respond regardless of the slave address programmed. The front panel RS232 program

port may be connected to a personal computer running the 489PC software. This program may be used for downloading

and uploading setpoint files, viewing measured parameters, and upgrading the 489 firmware to the latest revision.

For RS485 communications, each IS200ICCAH1ADB must have a unique address from 1 to 254. Address 0 is the broadcast address

which all relays listen to. Addresses do not have to be IS200ICCAH1ADB sequential but no two units can have the same address or conflicts

resulting in errors will occur. Generally each unit added to the link will use the next higher address starting at 1. Baud rates

can be selected as 300, 1200, 2400, 4800, 9600, or 19200. The data frame is fixed at 1 start, 8 data, and 1 stop bits, while

parity is optional. The computer RS485 port is a general purpose port for connection to a DCS, PLC, or PC. The Auxiliary

RS485 port may also be used as another general purpose port or it may be used to talk to Auxiliary GE Power Manage

ment Devices in the future.

For events that are recorded by the event recorder to be correctly time/date stamped, the correct time and date must be

entered. A battery backed internal clock runs IS200ICCAH1ADB continuously even when power is off. It has the same accuracy as an elec

tronic watch approximately ±1 minute per month. It must be periodically corrected either manually through the front panel or

via the clock update command over the RS485 serial link. If the approximate time an event occurred without synchroniza

tion to other relays is sufficient, then entry of time/date from the front panel keys is adequate.

If the RS485 serial communication link is used then all the relays can keep time in synchronization with each other. A new

clock time is pre-loaded into the memory map via the RS485 communications port by a remote computer to each relay con

nected on the communications channel. The computer IS200ICCAH1ADB broadcasts (address 0) a “set clock” command to all relays. Then all

relays in the system begin timing at the exact same instant. There can be up to 100 ms of delay in receiving serial com

mands so the clock time in each relay is ±100 ms, ± the absolute clock accuracy in the PLC or PC. See the chapter on

Communications for information on programming the time preload and synchronizing commands.

An IRIG-B signal receiver may be connected to 489 units with hardware revision G or higher. The relay will continuously

decode the time signal and set its internal time correspondingly. The “signal type” setpoint must be set to match the signal

provided by the receiver.

Why are the prices of many products of our company more competitive?
(1) Source purchase to reduce the price difference in the intermediate phase
(2) Stable channel and more guaranteed supply
Lead time problem
(1) For the spot products in stock, the de

The maximum number of 8-Channel Analog Current/Voltage Output modules that can be installed

in a system are:

4 in a system using CPU Models 311, 313, or 323

8 in a system using CPU Model 331

32 in a system using CPU Models 340 and 341

64 in a system using CPU Models 350 – 364

Other Configuration Considerations

When planning the module configuration for your application you must also consider the load

capacity of the installed power supply and the total load requirements of all modules that are

installed in the baseplate.

Refer to Chapter 1 in this manual for details on power supply, baseplate, and module load

requirements. The following table lists the specifications for this module. Note that test conditions,

unless otherwise noted, are: VUSER = 24 VDC at an ambient temperature of 25 C (77 F)

livery can be arranged on the same day after the contract payment is signed
(2) Order products and deliver according to the quoted delivery date
Xiamen Xiongba adheres to the enterprise philosophy of “improving the value of spare parts supply chain”,
For the simple purchase procedure of spare parts, ensure that they are delivered to the site in a timely manner, and help users reduce the risk of downtime caused by the shortage of spare parts
The emergency spare parts support service is complete, and the user can customize the spare parts. The quality of the spare parts is reliable. All the spare parts provided enjoy a one-year super long warranty
Spot stock, fast response, reduce user capital investment, improve spare parts utilization, spare parts replacement!

Details: If you need urgent delivery orders, please feel free to contact us, and we will try our best to meet your needs.
Price problem: If you find that other suppliers offer cheaper prices for the same product, we are also willing to provide you with reference prices and give you further discounts.
Contact us:+86 181 0693 7731
Mail: 2872270648@qq.com
Contact: Chen