PC833-001-N PC833-001-N-BA brushless servo driver

Description

PC833-001-N PC833-001-N-BA brushless servo driver

PC833-001-N PC833-001-N-BA brushless servo driver

There can be cause for concern when this p-p number exceeds 40% of the drive’s or motor’s current rating. The motor current should be monitored using Dac Monitors on J2-4 to insure actual ripple current, with ARF0/ARF1 filtering, is not excessive. Motor current ripple can often be reduced by lowering the ARF0, ARF1 low-pass filter break frequencies. This benefit is limited by velocity loop bandwidth and stability constraints. Velocity feedback ripple, and hence motor current ripple, can also be reduced by specifying a higher accuracy resolver.

Setting KVFF equal to 100% can result in position overshoot. Somewhat lower values may be required if this is a problem. KVFF set to 70%-80% typically achieves the fastest step response with no overshoot. However, setting KVFF to less than 100% will give steady state following error when running at constant speed.

The equipment described herein has been developed, produced, tested and documented in accordance with the corresponding standards. During use conforming with requirements, the equipment is not dangerous for people or equipment. Use conforming with requirements means that the safety recommendations and warnings detailed in this manual are complied with and that the applicable regulations for safety (machine directives, etc.) and noise suppression (EMC Directives) are observed while operating the drive. At the end of its lifetime, dispose of or recycle the drive according to the regulations applicable at that time.

Communication process description: The communication process specifically involves reading process data from the serial interface of the PLC device through different protocol devices into various “virtual” Slots in FTA, and then writing the data into the Image DataBase of APM through SI IOP. APM reads these data into the corresponding SI Array Point of the group state within a certain period of time (corresponding to the assigned address).

Communication process:
The process data that needs to participate in communication in the PLC is configured in the communication register, with the bit number corresponding to the address. The serial communication data block with the format (configuration address+process value+check bit) is sent to FTA through the serial communication line, and the address and process data are separated from the format data block. Reference the Array Point address corresponding to the Slot configured in the APM of DCS, and transfer the data to the correct Array Point. In Modbus FTA, data is scanned at a speed of 19.2Kbaud, while in Allen Bradley FTA, each Array Point can choose a different scanning method: A, free running (user-defined time scanning); B. Periodic (fixed period scanning); C. Report by exception (event triggered scanning RBE); In APM, there are three speeds for scanning data from Image DataBase (1/4 second, 1/2 second, and 1 second).

Recommended products:
3HAC022478-001
3HAC022479-001
3HAC022480-001
3HAC022481-001
3HAC022483-001
3HAC022483-002
3HAC022483-003
3HAC022483-004
3HAC022484-001
3HAC022491-001
3HAC022517-001
3HAC022517-002
3HAC022517-003
3HAC022517-004
3HAC022521-001
3HAC022542-001
3HAC022544-001
3HAC022544-008
3HAC022545-007
3HAC022546-001
3HAC022546-002
3HAC022546-003
3HAC022546-004
3HAC022546-005
3HAC022546-006
3HAC022546-007
3HAC022546-008
3HAC022546-009
3HAC022549-001
3HAC022578-001
3HAC022581-001
3HAC022611-001
3HAC022618-001
3HAC022620-001
3HAC022623-001
3HAC022626-001
3HAC022629-001
3HAC022637-001
3HAC022643-001
3HAC022644-001
3HAC022645-001
3HAC022648-001
3HAC022649-001
3HAC022650-001
3HAC022652-001
3HAC022657-003